| Can you make non-standard sizes?
|
|
Yes, up to 4' x 8'. Call for a quote. Shipping very large sizes may be a concern.
|
|
| What fabrics can I use?
|
|
Almost any except very sheer or thin fabrics. Could run or show through.
|
|
| Can you make 3 piece segmented designs without the magnetic strips?
|
|
Yes, Velcro, repositionable or permanent tape, or plain.
|
|
| Could the 3 pc. designs be used on a wall?
|
|
Yes, recommend repositionable tape.
|
|
| Are they available for 2 or 3 high files?
|
|
No, not enough area for 3 pc. design. Recommend single tackboard.
|
|
| Are there other designs available?
|
|
No. However, if volume is 50 or more, we could make a custom design.
|
|
| What is the construction of magnetic tackboards?
|
|
1/2" compressed fiberboard with fabric glued to face and pulled to back to create self edge.
|
|
| When I measure the height of my file - do I give the full height?
|
|
Yes, we will subtract 1-1/2" for toe kick and to avoid carpet interference.
|
|
| Which fabric is #1 and which is #2?
|
|
#1 covers the single tackboard piece and #2 covers the two tackboard pieces. This is correct on the order form and on website but incorrect in the binder ordering guidelines.
|
|
| Do I need to specify when I'm covering sides and back of the same file?
|
|
Yes, we will increase the size of the back tackboard to overlap the sides.
|
|
| Can a directional fabric be turned (railroaded) from the direction shown in the ordering guidelines?
|
|
Yes, however, there may be an added cost if fabric yield is reduced.
|
|
| Any lower prices for large quantities.? |
|
Yes. Call for a quote.
|
|
Tackboards / Systems Furniture
| Can you make sizes other than shown in catalog?
|
|
Yes, up to 4' x 8'. Call for quote. Shipping very large sizes may be an issue.
|
|
| What fabrics can I use?
|
|
Almost any except very sheer or thin fabrics. Could run or show through.
|
|
| What is the construction of systems tackboards?
|
|
Two sheets of compressed fiberboard sandwiched around hardboard to create an overall thickness of 7/8".
|
|
| Can you radius corners and edges?
|
|
Yes, small upcharge for small quantities.
|
|
| Can I specify the direction of fabric?
|
|
Yes, with possible upcharge if fabric yield is reduced.
|
|
| Do you pre-drill system mount tackboards or mount the brackets? |
|
No, however, we can get the brackets for you or recommend sources.
|
|
| Can you make non-standard sizes?
|
|
Yes, up to 4' x 8'. Call for a quote. Shipping very large sizes may be a concern.
|
|
| What fabrics can I use?
|
|
Almost any except very sheer or thin fabrics. Could run or show through.
|
|
| Can a directional fabric be turned (railroaded) from the direction shown in the ordering guidelines?
|
|
Yes, however, there may be an added cost if fabric yield is reduced.
|
|
| What is the construction of wall mount tackboards?
|
|
Either 1/2" compressed fiberboard with fabric glued to face and back, or two sheets of compressed fiberboard sandwiched around hardboard to create an overall thickness of 7/8".
|
|
| Can you radius corners and edges?
|
|
Yes, small upcharge for small quantities.
|
|
| Could the 3 pc. designs be used on a wall?
|
|
Yes, recommend repositionable tape.
|
|
| What are my options for the back of tackboards?
|
|
Permanent or repositionable tape, magnet strips, Velcro, or plain.
|
|
| How many times can I reposition the repositionable tape?
|
|
If you adhere to a clean surface and do not allow dust, dirt or skin oils to contact adhesive, it can be repositioned several times.
|
|
| Any lower prices for large quantities? |
|
Yes, call for a quote.
|
|
|
